Need More Help? 718-499-1119
Search
Dremel
Dremel branded products
DREMEL 570 Grout Removal Bit, 1/8 in Dia, 1-1/2 in L, 10 mm L Flute, 1/8 in Dia Shank, Steel
D032-01225
- Easily remove both wall and floor grout
- A high-speed cutter with a 1/8 in steel shank
- A high-speed cutter with a 1/8 in steel shank
- 30 deg angle for controlled cutting
- Guides 180 deg apart to keep bit centered
DREMEL 516 Abrasive Point, 1/8 in Dia Shank
D032-01187
- Ideal for sharpening, deburring and general-purpose grinding on harder materials including stone, glass, ceramic, porcelain, gemstones and non-ferrous metals specially designed for working with conic and flat surfaces
- Use a sanding band or small piece of sandpaper to clean the surface of the abrasive point and restore its original shape
- Use a sanding band or small piece of sandpaper to clean the surface of the abrasive point and restore its original shape
- Can be used for paint and rust removal without removing any of the base metal
- For top results, insert the accessory bit all the way into the tool and then back it out slightly before tightening down, this provides plenty of shank for the collet or chuck to hold onto the bit
DREMEL 220-01 Drill Press, 2 in Drilling
D032-02262
- Articulating drill press drills perpendicular and angled holes in 15 deg increments, up to 90 deg horizontal
- Flex shaft tool stand allows telescopic adjustment between 16 in and 29 in height
- Flex shaft tool stand allows telescopic adjustment between 16 in and 29 in height
- Tool holder holds tool at 90 deg horizontal for tasks such as polishing metal objects, sanding different shapes and grinding metal pieces
- Crow's nest provides on-board storage for drill bits, wrenches and other Dremel accessories
DREMEL 200-1/15 Rotary Tool Kit, 0.9 A, 1/8 in Chuck, Keyed Chuck, 2-Speed, 15,000 to 35,000 rpm Spe
D032-02900
- Two-speed control allows you to set your speed at 15,000 or 35,000 rpm with a flip of a switch
- Click-and-set On/Off switch allows precise speed selection
- Click-and-set On/Off switch allows precise speed selection
- Cool-running ball bearing construction for smooth and quiet operation
- Replaceable motor brushes extend tool life
DREMEL MM920 Carbide Rasp, 24 Grit, 3.14 in L
D032-03024
- Carbide rasp accessory allows the multi-max to be used for rasping and grinding
- Use on cement, plaster, thin-set mortar and wood
- Preparing the surface for tile replacement is a common application for this accessory
- Versatile accessory
- Versatile accessory
DREMEL SM500 Cut-Off Wheel, 3 in Dia, 0.07 in Thick, 20 mm Arbor, Silicone Carbide Abrasive
D032-03282
- Carbide cutting grit for a variety of high-performance cutting applications
- Do not apply excessive pressure let the tool do the work
- Maximum recommended cutting thickness is 3/4 in
- For cutting applications
DREMEL SM600 Cut Wheel, 3 in Dia, 0.075 in Thick, 1 in Arbor, Silicone Carbide Abrasive
D032-03286
- Dome-shaped wheel for flush cuts up 3/4 in
- Carbide cutting grit for a variety of high-performance cutting applications
- Do not apply excessive pressure let the tool do the work
- For cutting baseboards for flooring installation
DREMEL 26150117AC Cutter, 1/4 in Dia, 1-1/2 in L, 1/8 in Dia Shank, HSS
D032-03521
- Use the sides of the cutter rather than the tip for effective cutting
- Use higher speeds for hard woods, slower speeds for metals and very slow speeds for plastics
- Use higher speeds for hard woods, slower speeds for metals and very slow speeds for plastics
- A versatile, high-quality cutter made of high-grade steel
- For shaping, hollowing, grooving, slotting, inlaying, making tapered holes
DREMEL MM910 Diamond Paper, 60 Grit, 3-1/2 in L
D032-03773
- Designed for light grinding, shaping and smoothing
- Use on masonry, thin-set, mortar and rust
- Use on masonry, thin-set, mortar and rust
- Preparing the surface for tile replacement is a common application for this accessory
- Ideal for removing paint or oil stains from driveways, excess mortar from bricks and rust from patio furniture
DREMEL 7103 Rotary Tool Bit, 5/64 in Dia, 1-1/2 in L, 1/8 in Dia Shank
D032-07103
- Removes material quickly and easily
- Bits are covered with diamond particles
- Bits are covered with diamond particles
- For fine detail work, cutting, engraving, carving, touch-up and finishing
- For best results, insert the accessory bit all the way into the tool and then back it out slightly before tightening down, this provides plenty of shank for the collect or chuck to hold onto the bit
DREMEL 7105 Rotary Tool Bit, 11/64 in Dia, 1-1/2 in L, 1/8 in Dia Shank
D032-07105
- Removes material quickly and easily
- Bits are covered with diamond particles
- Bits are covered with diamond particles
- Use higher speeds for hard woods and slower speeds for metals
- For fine detail work, cutting, engraving, carving, touch-up and finishing
DREMEL 7122 Rotary Tool Bit, 3/32 in Dia, 1-1/2 in L, 1/8 in Dia Shank, HSS
D032-07122
- Removes material quickly and easily
- Bits are covered with diamond particles
- Bits are covered with diamond particles
- Use higher speeds for hard woods and slower speeds for metals
- For fine detail work, cutting, engraving, carving, touch-up and finishing
DREMEL 7120 Rotary Tool Bit, 16/64 in Dia, 1-1/2 in L, 1/8 in Dia Shank
D032-07120
- Removes material quickly and easily
- Bits are covered with diamond particles
- Bits are covered with diamond particles
- Use higher speeds for hard woods and slower speeds for metals
- For fine detail work, cutting, engraving, carving, touch-up and finishing
DREMEL 7123 Rotary Tool Bit, 3/16 in Dia, 1-1/2 in L, 1/8 in Dia Shank
D032-07123
- Removes material quickly and easily
- Bits are covered with diamond particles
- Bits are covered with diamond particles
- For fine detail work, cutting, engraving, carving, touch-up and finishing
DREMEL 9905 Cutter, 1/8 in Dia, 1-1/2 in L, 1/8 in Dia Shank, Tungsten Carbide
D032-09905
- A high-speed cutter made of tungsten carbide, the hardest material next to diamond
- A versatile, high-quality cutter
- A versatile, high-quality cutter
- For shaping, smoothing or removing material from especially hard substances
DREMEL 9906 Cutter, 1/8 in Dia, 1-1/2 in L, 1/8 in Dia Shank, Tungsten Carbide
D032-09906
- A high-speed cutter made of tungsten carbide, the hardest material next to diamond
- Use higher speeds for hard woods, slower speeds for metals and very slow speeds for plastics
- Use higher speeds for hard woods, slower speeds for metals and very slow speeds for plastics
- Use the sides of the cutter rather than the tip for effective cutting
- For shaping, smoothing or removing material from especially hard substances
DREMEL 9909 Cutter, 1/8 in Dia, 1-1/2 in L, 1/8 in Dia Shank, Tungsten Carbide
D032-09909
- Made of tungsten carbide, the hardest material next to diamond
- Shapes, smoothes or grinds especially hard materials
- Shapes, smoothes or grinds especially hard materials
- High-speed cutter
- For shaping, smoothing or removing material from especially hard substances
DREMEL 9911 Cutter, 1/8 in Dia, 1-1/2 in L, 1/8 in Dia Shank, Tungsten Carbide
D032-09911
- A high-speed cutter made of tungsten carbide, the hardest material next to diamond
- Use higher speeds for hard woods, slower speeds for metals and very slow speeds for plastics
- Use higher speeds for hard woods, slower speeds for metals and very slow speeds for plastics
- Use the sides of the cutter rather than the tip for effective cutting
- For shaping, smoothing or removing material from especially hard substances
Payment options
